catalogue

Dek-Master® 31.5 mil Series (Limited Quantities) Vinyl Components

View technical information

Dek-Master®  31.5 mil Vinyl - West Coast Grey - Limited Quantities Part No. 150-10075

Description:  A fully cured PVC vinyl material impregnated onto a polyester fabric backing.

Features: Waterproof, Long Lasting, Fade and Mildew Resistant, Non-Skid, Easy to Clean, Cool to the Touch, Easy to Install.

Uses:  Commonly used to waterproof Sundecks, Balconies, RV Roof Tops, Sun Rooms, Boats and Boathouses. Will adhere to Plywood, Metals, Fiberglass, Above Ground Concrete and Rubberized Coatings.

NOTE: 74" width - Sold by the linear foot - Roll length 150 lin ft - Can be cut to length.

NOTE: Colour may not be exactly as shown.

Dek-Master®  31.5 mil Vinyl - Desert Beige - Limited Quantities Part No. 150-10076

Description:  A fully cured PVC vinyl material impregnated onto a polyester fabric backing.

Features: Waterproof, Long Lasting, Fade and Mildew Resistant, Non-Skid, Easy to Clean, Cool to the Touch, Easy to Install.

Uses:  Commonly used to waterproof Sundecks, Balconies, RV Roof Tops, Sun Rooms, Boats and Boathouses. Will adhere to Plywood, Metals, Fiberglass, Above Ground Concrete and Rubberized Coatings.

NOTE: 74" width - Sold by the linear foot - Roll length 150 lin ft - Can be cut to length.

NOTE: Colour may not be exactly as shown.

Dek-Master®  31.5 mil Vinyl - Seafoam - LIMITED QUANTITIES Part No. 150-10079

Description:  A fully cured PVC vinyl material impregnated onto a polyester fabric backing.

Features: Waterproof, Long Lasting, Fade and Mildew Resistant, Non-Skid, Easy to Clean, Cool to the Touch, Easy to Install.

Uses:  Commonly used to waterproof Sundecks, Balconies, RV Roof Tops, Sun Rooms, Boats and Boathouses. Will adhere to Plywood, Metals, Fiberglass, Above Ground Concrete and Rubberized Coatings.

NOTE: 74" width - Sold by the linear foot - Roll length 150 lin ft - Can be cut to length.

NOTE: Colour may not be exactly as shown.

Dek-Master®  31.5 mil Vinyl - Brindle Taupe - LIMITED QUANTITIES Part No. 150-10078

Description:  A fully cured PVC vinyl material impregnated onto a polyester fabric backing.

Features: Waterproof, Long Lasting, Fade and Mildew Resistant, Non-Skid, Easy to Clean, Cool to the Touch, Easy to Install.

Uses:  Commonly used to waterproof Sundecks, Balconies, RV Roof Tops, Sun Rooms, Boats and Boathouses. Will adhere to Plywood, Metals, Fiberglass, Above Ground Concrete and Rubberized Coatings.

NOTE: 74" width - Sold by the linear foot - Roll length 150 lin ft - Can be cut to length.

NOTE: Colour may not be exactly as shown.

Dek-Patch Filler & Floor Levelling Compound - 2 lb Part No. 150-20101

Description: A modified cement based compound for filling and leveling T & G plywood joints, screw holes, transitions between wood and flashing or cant strip.

Features: Easy to apply, fast dry time, sandable, mixes easily with 2 parts Dek-Patch, 1 part water.

Uses: As a joint crack and hole filler and leveler. To be used on new plywood surfaces under all Dek-Master® vinyls.

NOTE: Spread rate 64 sq ft per quart or 2 sheets of plywood.

 

Dek-Patch Filler & Floor Levelling Compound - 8 lb Part No. 150-20104

Description: A modified cement based compound for filling and leveling T & G plywood joints, screw holes, transition between wood and flashing or cant strip.

Features: Easy to apply, fast dry time, sandable, mixes easily with 2 parts Dek-Patch, 1 part water.

Uses: As a joint crack and hole filler and leveler. To be used on new plywood surfaces under all Dek-Master® vinyls.

NOTE: Spread rate 256 sq ft per gallon or 8 sheets of plywood.

Dek-master® water based regular adhesive - 1 gal Part No. 150-20204

Description: A water based latex rubber adhesive specially formulated for laying 31.5 mil PVC vinyl floor coverings and carpets with many different backings. For use both outdoors and indoors. Apply with a low nap paint roller.

Features: Waterproof, extremely user friendly in extreme cold weather. Allows up to 60 minutes of working time. Low odour. White, dries to clear.

Uses: Adhering Ducan Dek-Master® 31.5 mil vinyl in a temperature range of 15° C to 30° C (59°F to 86°F).

NOTE: 1 Gal will cover 64 sq ft of deck surface. (1 coat on back of vinyl and 1 on the wood)

dek-master® WATER BASED regular adhesive - 3 gal Part No. 150-20211

Description: A water based latex rubber adhesive specially formulated for laying 31.5 mil PVC vinyl floor coverings and carpets with many different backings. For use both outdoors and indoors. Apply with a low nap paint roller.

Features: Waterproof, extremely user friendly in extreme cold weather. Allows up to 60 minutes of working time. Low odour. White, dries to clear.

Uses: Adhering Ducan Dek-Master® 31.5 mil vinyl in a temperature range of 15° C to 30° C (59°F to 86°F).

NOTE: 3 Gal will cover 192 sq ft of deck surface. (1 coat on back of vinyl and 1 on the wood)

Dek-Master® Low Temp Adhesive - 1 Gal Part No. 150-20604

Description: A solvent based neoprene adhesive especially formulated for exterior vinyl application with a low nap paint roller suitable for enamel paints.

Features: Waterproof, flexible in extreme hot and cold weather. User friendly allowing up to 1 hour of working time (exterior use).

Uses: Adhering Ducan Dek-Master® 31.5 mil vinyl in temperature range of 8° C to 15° C (45°F to 59°F).

NOTE: 1 Gal will cover 64 sq ft of deck surface. (1 coat on back of vinyl and 1 on the wood)

Dek-Master® Low Temp Adhesive - 2.5 Gal Part No. 150-20610

Description: A solvent based neoprene adhesive specially formulated for exterior vinyl application with a low nap paint roller suitable for enamel paints.

Features: Waterproof, flexible in extreme hot and cold weather. User friendly allowing up to 1 hour of working time (exterior use).

Uses: Adhering Ducan Dek-Master® 31.5 mil vinyl in temperature range of 8° C to 15° C (45°F to 59°F).

NOTE: 1 - 2.5 Gal will cover 160 sq ft of deck surface. (1 coat on back of vinyl and 1 on the wood)

Dek-Master® Trim Adhesive - 1 Qt Part No. 150-20611

Description: A solvent based neoprene adhesive especially formulated for exterior vinyl application with a low nap paint roller or a paint brush suitable for enamels.

Features: Waterproof, flexible in extreme hot and cold weather. User friendly allowing up to 15 minutes working time (exterior use).

Uses: Adhering Ducan Dek-Master® 31.5 mil and 45 mil vinyls to metal trims in temperature range of 8° C to 32° C (45°F to 90°F).

NOTE: 1 Qt will cover approximately 60 lin ft of metal trim.

 

DEK-MASTER® Overlap Cement - 8 fl oz Part No. 150-20525

Description: A PVC vinyl/acrylic blend solvent cement for sound waterproof Dek-Master® 31.5 mil vinyl overlap seams.

Features: Waterproof, non-yellowing, easy to apply and flexible in extreme cold.

Uses: To chemically weld and waterproof Dek-Master® 31.5 mil vinyl overlap seams, outside corners, inside corners. Do not apply below 8° C

NOTE: 1 can will do approx. 25 linear feet of seam based on a 1 inch overlap.

Dek-master Caulking - White 300 ml
Part No. 175-20438

Description: A sealant that is an extremely flexible, single component, non-sag elastomer that bonds to wood, concrete, brick, stucco, and metals.

Features: High rubber content, flexible in cold weather, low shrinkage, paintable, non-staining and can be used in cold weather.

Uses: A deck caulking compound used around posts, up against the house where the vinyl and cant strip meet the house, or any place where moisture may threaten to seep in.

NOTE: 1 container will cover approximately 25 linear feet.

 

Dek-master Caulking - Grey 300 ml
Part No. 175-20439

Description: A sealant that is an extremely flexible, single component, non-sag elastomer that bonds to wood, concrete, brick, stucco, and metals.

Features: High rubber content, flexible in cold weather, low shrinkage, paintable, non-staining and can be used in cold weather.

Uses: A deck caulking compound used around posts, up against the house where the vinyl and cant strip meet the house, or any place where moisture may threaten to seep in.

NOTE: 1 container will cover approximately 25 linear feet.

Dek-master Caulking - Buff 300 ml
Part No. 175-20437

Description: A sealant that is an extremely flexible, single component, non-sag elastomer that bonds to wood, concrete, brick, stucco, and metals.

Features: High rubber content, flexible in cold weather, low shrinkage, paintable, non-staining and can be used in cold weather.

Uses: A deck caulking compound used around posts, up against the house where the vinyl and cant strip meet the house, or any place where moisture may threaten to seep in.

NOTE: 1 container will cover approximately 25 linear feet.

Galvanized Metal Drip Flashing- non return - 6 ft
Part No. 170-70736

Description: 30 gauge galvanized metal flashing with non-return drip edge.

Features: Galvanized metal will not rust. Non-return drip edge to lead water away allowing the fascia board to stay dry.

Uses: Nail down 1/4" off the fascia board around the outside perimeter of the deck.

Galvanized Metal Cant Strip - 6 ft
Part No. 175-70737

Description: 30 gauge galvanized metal cant strip to replace the use of wooden cant strip.

Features: Galvanized metal will not rust. Recessed back edge to allow for smooth, even caulking line.

Uses: Cant strip is nailed down in front of the building wall to allow a smooth transition between the deck and the wall. This will allow water to flow easily off of the wall and onto the deck.

U-Channel - White 6 ft
Part No. 175-70730

Description: Finishing edge for a professionally finished look to the deck.

Features: Easy to install friction fit. Clean looking finishing edge.

Uses: To clip over the vinyl and flashing edge. Prevents curling of vinyl from the edge of the flashing.

U-Channel - Beige 6 ft
Part No. 175-70732

Description: Finishing edge for a professionally finished look to the deck.

Features: Easy to install friction fit. Clean looking finishing edge.

Uses: To clip over the vinyl and flashing edge. Prevents curling of vinyl from the edge of the flashing.

U-Channel - Grey 6 ft
Part No. 175-70734

Description: Finishing edge for a professionally finished look to the deck.

Features: Easy to install friction fit. Clean looking finishing edge.

Uses: To clip over the vinyl and flashing edge. Prevents curling of vinyl from the edge of the flashing.

Roller Sleeve
Part No. 175-70009

Description: Roller suitable for applying solvent and water based adhesives.

Features: A flamed bonding process that embeds the fleece into the core. This allows the roller to perform with solvents without falling apart.

Uses: For applying adhesives to the deck surface as well as to the back side of the vinyl.

The Duke
Part No. 175-30612

Description: A chemically activated, concentrated, all purpose cleaner and degreaser.

Features: Bio-degradable, economical, buffered pH, pleasant clean odour, free rinsing, non-flammable, convenient 1.9 L size dilutes to make up to 40 litres.

Uses: Ideally suited for cleaning and degreasing all around the house, yard, car, boats, RV's, Dek-Master® vinyls, sundecks, patios, concrete driveways, garden equipment, painted walls, fiberglass, aluminum and vinyl siding.

NOTE: Must be diluted with water to activate.

 

Dek-Master® Wood deck drain assembly Part No. 175-WDD1

Description: The Deck Drain Assembly is designed for wood decks.

Features: Composed of 3 parts: the grate, the clamp collar and the drain body. It has a 6 1/2" deck opening with the 3 deck flange screws set at 7 3/4" diameter. The flange is 8" in diameter..

Uses: Designed for use on a plywood deck surface that is being covered with a vinyl membrane.

NOTE: Easy installation instructions included with each drain assembly.

Technical Information

Dek-Master Vinyl 31.5 mil thickness
Residential & light commercial usage
Width 74 "
Roll length 150 lineal feet
PVC Vinyl/Fabric thickness 31.5 mil.
Waterproof adhesive layer (dry) 10 to 15 mil.
Overall thickness including adhesive 40 to 45 mil.
Weight per Roll (150 lin. ft.) 21 oz/sq. yd. (150 lbs/roll)
Fabric backing Needled non-woven polyester
Grab Tensile Strength
ASTM D751.66
Warp 75 min. (Lengthwise)
Fill 75 min. (Crosswise)
Trap Tear Strength
Federal Standard #181
Warp 15 min. (Lengthwise)
Fill 15 min. (Crosswise)
Fade Resistance
ASTM G2575
No appreciable colour change after accelerated exposure to 1,000 hours weatherometer and/or fadeometer
Mildew Resistance  ASTM G1160 1 mm minimum zone of inhibition on both sides
Slip Resistance  ASTM C1028 Complies with the A.D.A. requirement for walkways
Abrasion Test  ASTM D4060 Passed with only slight wear (:003)
Chemical/Stain Resistance
ASTK D2195
Passed-no appreciable change in colour or physical property
Flammability Resistance MUSS #302 Pass
Warranty 3 Year Limited 5 year limited if installed by Authorized Installer

« Back to Catalogue ^ back to top
  • I can honestly recommend Ducan products and by doing it myself saved nearly $5000.00 on a 450 square foot deck! Steve Anthony, Okanagan Falls, BCread more »