Catalogue

Dek-Master® 60 mil Pro-Series Vinyl Components

View technical information

Dek-Master® PRO-SERIES 60 mil CERTIFIED Vinyl - CANYON GREY Part No. 150-10094

Description:  A fully cured PVC vinyl material impregnated onto a polyester fabric backing.

Features: Waterproof, Long Lasting, Fade and Mildew Resistant, Non-Skid, Easy to Clean, Cool to the Touch, Easy to Install.

Uses:  Commonly used to waterproof Sundecks, Balconies, RV Roof Tops, Sun Rooms, Boats and Boathouses. Will adhere to Plywood, Metals, Fiberglass, Above Ground Concrete and Rubberized Coatings.

NOTE: 72" width - Sold by the linear foot - Roll length 75 lin ft - Can be cut to length.

Dek-Master® PRO-SERIES 60 mil CERTIFIED Vinyl - FIELDSTONE Part No. 150-10096

Description:  A fully cured PVC vinyl material impregnated onto a polyester fabric backing.

Features: Waterproof, Long Lasting, Fade and Mildew Resistant, Non-Skid, Easy to Clean, Cool to the Touch, Easy to Install.

Uses:  Commonly used to waterproof Sundecks, Balconies, RV Roof Tops, Sun Rooms, Boats and Boathouses. Will adhere to Plywood, Metals, Fiberglass, Above Ground Concrete and Rubberized Coatings.

NOTE: 72" width - Sold by the linear foot - Roll length 75 lin ft - Can be cut to length.

Dek-Master® PRO-SERIES 60 mil CERTIFIED Vinyl - MUSKOKA SHORE Part No. 150-10097

Description:  A fully cured PVC vinyl material impregnated onto a polyester fabric backing.

Features: Waterproof, Long Lasting, Fade and Mildew Resistant, Non-Skid, Easy to Clean, Cool to the Touch, Easy to Install.

Uses:  Commonly used to waterproof Sundecks, Balconies, RV Roof Tops, Sun Rooms, Boats and Boathouses. Will adhere to Plywood, Metals, Fiberglass, Above Ground Concrete and Rubberized Coatings.

NOTE: 72" width - Sold by the linear foot - Roll length 75 lin ft - Can be cut to length.

Dek-Patch Filler & Floor Levelling Compound - 2 lb Part No. 150-20101

Description: A modified cement based compound for filling and leveling T & G plywood joints, screw holes, transitions between wood and flashing or cant strip.

Features: Easy to apply, fast dry time, sandable, mixes easily with 2 parts Dek-Patch, 1 part water.

Uses: As a joint crack and hole filler and leveler. To be used on new plywood surfaces under Dek-Master® vinyls.

NOTE: Spread rate 64 sq ft per quart or 2 sheets of plywood.

 

 

Dek-Patch Filler & Floor Levelling Compound - 8 lb Part No. 150-20104

Description: A modified cement based compound for filling and leveling T & G plywood joints, screw holes, transition between wood and flashing or cant strip.

Features: Easy to apply, fast dry time, sandable, mixes easily with 2 parts Dek-Patch, 1 part water.

Uses: As a joint crack and hole filler and leveler. To be used on new plywood surfaces under Dek-Master® vinyls.

NOTE: Spread rate 256 sq ft per gallon or 8 sheets of plywood.

 

 

Dek-Master® SNAPTAC FAST DRY ADHESIVE - 1 GAL Part No. 150-20304

Description: A solvent based neoprene rubber contact adhesive especially formulated for exterior vinyl applications. Very fast tack time for use on 45 mil and 60 mil vinyls.

Features: Waterproof, flexible in extreme hot and cold weather. Extremely fast tack time (exterior use).

Uses: Adhering Dek-Master® 45 mil and 60 mil vinyls. Spread rate 46 sq ft.

NOTE: 1 Gal pail will cover 46 sq ft of deck surface. (1 coat on back of vinyl and 1 on wood)

 

 

Dek-Master® SNAPTAC FAST DRY ADHESIVE - 2.5 GAL  

Description: A solvent based neoprene rubber contact adhesive especially formulated for exterior vinyl applications. Very fast tack time for use on 45 mil and 60 mil vinyls.

Features: Waterproof, flexible in extreme hot and cold weather. Extremely fast tack time (exterior use).

Uses: Adhering Dek-Master® 45 mil and 60 mil vinyls. Spread rate 115 sq ft.

NOTE: 2.5 Gal pail will cover 115 sq ft of deck surface. (1 coat on back of vinyl and 1 on wood)

 

 

Dek-Master® Pro-Series Exterior Contact adhesive - 5 Gal
Part No. 150-20320

Description: A solvent based neoprene rubber contact adhesive especially formulated for exterior vinyl applications. Very fast tack time for use on 45 mil and 60 mil vinyls.

Features: Waterproof, flexible in extreme hot and cold weather. Extremely fast tack time (exterior use).

Uses: Adhering Dek-Master® 45 mil and 60 mil vinyls. Spread rate 46 sq ft per gallon.

NOTE: 5 Gal pail will cover 230 sq ft of deck surface. (1 coat on back of vinyl and 1 on wood)

 

DEK-MASTER® WHITE DECK CAULK/SEALANT - 318 ML Part No. 175-20438

Description: A sealant that is an extremely flexible, single component, non-sag elastomer that bonds to wood, concrete, brick, stucco, and metals.

Features: High rubber content, flexible in cold weather, low shrinkage, paintable, non-staining and can be used in cold weather.

Uses: A deck caulking compound used around posts, up against the house where the vinyl and cant strip meet the house, or any place where moisture may threaten to seep in.

NOTE: 1 container will cover approximately 25 linear feet.

 

DEK-MASTER® GREY DECK CAULK/SEALANT - 318 ML Part No. 175-20439

Description: A sealant that is an extremely flexible, single component, non-sag elastomer that bonds to wood, concrete, brick, stucco, and metals.

Features: High rubber content, flexible in cold weather, low shrinkage, paintable, non-staining and can be used in cold weather.

Uses: A deck caulking compound used around posts, up against the house where the vinyl and cant strip meet the house, or any place where moisture may threaten to seep in.

NOTE: 1 container will cover approximately 25 linear feet.

 

DEK-MASTER® BUFF DECK CAULK/SEALANT - 318 ML Part No. 175-20437

Description: A sealant that is an extremely flexible, single component, non-sag elastomer that bonds to wood, concrete, brick, stucco, and metals.

Features: High rubber content, flexible in cold weather, low shrinkage, paintable, non-staining and can be used in cold weather.

Uses: A deck caulking compound used around posts, up against the house where the vinyl and cant strip meet the house, or any place where moisture may threaten to seep in.

NOTE: 1 container will cover approximately 25 linear feet.

 

DEK-MASTER® GALVANIZED METAL FLASHING - 6 FT Part No. 170-70736

Description: 30 gauge galvanized metal flashing with non-return drip edge.

Features: Galvanized metal will not rust. Non-return drip edge to lead water away allowing the fascia board to stay dry.

Uses: Nail down 1/4" off the fascia board around the outside perimeter of the deck.

DEK-MASTER® GALVANIZED METAL CANT STRIP - 6 FT Part No. 175-70737

Description: 30 gauge galvanized metal cant strip to replace the use of wooden cant strip.

Features: Galvanized metal will not rust. Recessed back edge to allow for smooth, even caulking line.

Uses: Cant strip is nailed down in front of the building wall to allow a smooth transition between the deck and the wall. This will allow water to flow easily off of the wall and onto the deck.

DEK-MASTER® WHITE PLASTIC U-CHANNEL - 6 FT PART NO. 150-70730

Description: Finishing edge for a professionally finished look to the deck.

Features: Easy to install friction fit. Clean looking finishing edge.

Uses: To clip over the vinyl and flashing edge. Prevents curling of vinyl from the edge of the flashing.

DEK-MASTER® BEIGE PLASTIC U-CHANNEL - 6 FT PART NO. 150-70732

Description: Finishing edge for a professionally finished look to the deck.

Features: Easy to install friction fit. Clean looking finishing edge.

Uses: To clip over the vinyl and flashing edge. Prevents curling of vinyl from the edge of the flashing.

DEK-MASTER® GREY PLASTIC U-CHANNEL - 6 FT PART NO. 150-70734

Description: Finishing edge for a professionally finished look to the deck.

Features: Easy to install friction fit. Clean looking finishing edge.

Uses: To clip over the vinyl and flashing edge. Prevents curling of vinyl from the edge of the flashing.

roller sleeve - 9" Part No. 175-70009

Description: Roller suitable for applying solvent and water based adhesives.

Features: A flamed bonding process that embeds the fleece into the core. This allows the roller to perform with solvents without falling apart.

Uses: For applying adhesives to the deck surface as well as to the back side of the vinyl.

THE DUKE® CONCENTRATED CLEANER & DEGREASER Part No. 175-30612

Description: A chemically activated, concentrated, all purpose cleaner and degreaser.

Features: Bio-degradable, economical, buffered pH, pleasant clean odour, free rinsing, non-flammable, convenient 1.9 L size dilutes to make up to 40 litres.

Uses: Ideally suited for cleaning and degreasing all around the house, yard, car, boats, RV's, Dek-Master® vinyls, sundecks, patios, concrete driveways, garden equipment, painted walls, fiberglass, aluminum and vinyl siding.

NOTE: Must be diluted with water to activate.

 

 

Dek-Master® Wood deck drain assembly
Part No. 175-WDD1
 

Description: The Deck Drain Assembly is designed for wood decks.

Features: Composed of 3 parts: the grate, the clamp collar and the drain body. It has a 6 1/2" deck opening with the 3 deck flange screws set at 7 3/4" diameter. The flange is 8" in diameter..

Uses: Designed for use on a plywood deck surface that is being covered with a vinyl membrane.

NOTE: Easy installation instructions included with each drain assembly.

 

Technical Information

Dek-Master Vinyl 60 mil thickness
Heavy Residential & Commercial usage (roof deck approved)
Width 72 "
Roll length 75 lineal feet
PVC Vinyl/Fabric thickness 75 mil
Waterproof adhesive layer (dry) 10 to 15 mil
Overall thickness including adhesive 85 to 90 mil
Weight per Roll (75 lin. ft.) 63 oz/sq. yd. (220 lb/roll)
Fabric backing needled non-woven polyester
Grab Tensile Strength
ASTM D-882
Warp 104 min. (Lengthwise)
Fill 93 min. (Crosswise)
Trapezoid Tear Strength
Federal Standard ASTM D-1004
Warp 17 min. (Lengthwise)
Fill 17 min. (Crosswise)
Fade Resistance
ASTM G-2575
No appreciable colour change after accelerated exposure to 1,000 hours weatherometer and/or fadeometer
Mildew Resistance  ASTM G-1280 1 mm minimum zone of inhibition on both sides
Slip Resistance  ASTM C-1028 Complies with the A.D.A. requirement for walkways
Abrasion Test ASTM D4060 Passed with only slight wear (:003)
Chemical/Stain Resistance
ATTM D-2195
Passed-no appreciable change in colour or physical property
Code Roofing Meets CGSB specifications and 37-GP-54M standards
Flammability Resistance MUSS #302 Pass

Warranty 7 Year Limited

10 Year Limited if Installed by Ducan Authorized Installer

« Back to Catalogue ^ back to top
  • I can honestly recommend Ducan products and by doing it myself saved nearly $5000.00 on a 450 square foot deck! Steve Anthony, Okanagan Falls, BCread more »